High Efficiency Twin Screw Extruder- China Factory Suppliers Manufacturers

Nanjing JIEYA hereby sincerely invited you to attend 2021  China (Hainan) Degradation Exhibition.

Our booth no.: B06

Time: June 23-25

Add: Hainan International Convention and Exhibition Center

We warmly welcome your coming and look forward to cooperate with you ;)

Nanjing Team sincerely invite you to attend The 15th China Chongqing Rubber, Plastics Industry Exhibition.

Our booth no.: S2544

Time: May 27-30, 2021

Address: Chongqing International Expo Center 

Wish to meet you at there ;)

The twin screw extruder's standard equipment includes a sturdy base frame dedicated to housing the temperature control unit and oil lubrication system. The equipment features advanced control software for seamless integration into digital factories, ready for Industry 4.0, greatly improving ease of use. The following is a detailed description of the operating procedures of the twin screw extruder.

 

Here is the content list:

l Start up operation

l Stop the machine

l Precautions

 

Start up operation

1.Close the power main gate of the twin screw extruder.

2. Turn on the power at the operation panel: Press and hold the power button clockwise to turn and then release.

3. Set the temperature of each temperature zone: for example, a zone temperature according to the process requirements set the corresponding temperature, press the set button, and then adjust the up and down arrows to the desired temperature, press the set button.

4. Set the feeding rate: according to the process, requirements can be fed rate between 0 ~ 10 to set.

5. Set the host speed of the twin screw extruder: set the host speed between 0~30 according to the process requirements.

6. Add cooling water to the cooling tank.

7. In turn on the fan: press the operation button on the operation panel.

8. When you need to start the operation of the vacuum pump, you can start the vacuum pump.

9. Turn on the cutter switch.

 

Stop the machine

1. Twin screw extruder normal stopping sequence: stop the feeder: close the vacuum line valve, open the vacuum chamber on the cover; gradually reduce the main screw speed; shut down the pelletizer and other auxiliary equipment: off the motor, each external water inlet valve.

2. Twin screw extruder emergency stop: (1) in case of an emergency need to stop the host, you can quickly press the electrical control cabinet red emergency stop button, and the host and the feed speed knob back to zero, and then the total power switch off. After eliminating the fault, you can restart the machine again in normal driving order. (2) encounter equipment automatic protection trip stop: need to set the various parameters knob to zero, and then reset the parameters, press the reset button and start the machine again.

 

Precautions

1. The normal production of the first shift machine, be sure to first check whether the barrel, hopper seal is the original closed kind, such as changes or damage, should check the hopper, the machine inside the Jane there are no foreign objects.

2. Pay attention to the screw to start at a low speed, the air time can not exceed 3min.

3. Must pay attention to check the purity of each batch of material, do not allow any impurities mixed into the material.

4. The beginning of the material to pay attention to the first small amount, evenly added material, while paying attention to observe the current meter (torque meter) pointer changes.

For granular material, use metering to add material. When you first start to feed production, be sure to pay attention to the extruder production work overload phenomenon. After the forming die lip out of the material, and then gradually increase the screw speed as appropriate.

5. Often check the working condition of the motor carbon brush, abnormalities should be replaced or adjusted promptly.

6. The screw cleaning work is not allowed to use steel tools scraping material, the application of copper brush, shovel cleaning.

7. When the process temperature is suspected of displaying problems on the instrument, use mercury temperature, meter actual measurement of the machine Jane, and molding mold degree. Refer to the mercury temperature measured temperature, adjust the calibration instrument to show the temperature.

 

If you still have questions, you can consult our company. Our company's website is https://www.njjyextrusion.com/

2022 CIM: Compounding Intelligent Manufacturing Conference is coming.
Nanjing Jieya team warmly welcome your visiting.
Booth no.: E10
Date: 2022.9.14-16
Address: Suzhou, China

See you~

The extrusion technology used by the single screw extruder is making waves in the food production industry. We know that single screw extruder can mass produce enterprise products of various shapes and textures. It allows a seamless and continuous operation process, which means that this means lower costs and higher production and sales.

• What are the reasons and solutions for the poor discharge or blockage of the single screw extruder head?

• What is the importance of single screw extruder temperature control?

• What is the importance of single screw extruder speed control?

What are the reasons and solutions for the poor discharge or blockage of the single screw extruder head?

1. Reasons: (1) A certain section of the heater does not work, and the material is poorly plasticized. (2) The operating temperature is set too low, or the molecular weight distribution of the plastic is wide and unstable. (3) There may be foreign objects in the single screw extruder that are not easy to melt.

2. Treatment method: (1) Check the heater and replace it if necessary. (2) Verify the set temperature of each section, negotiate with the technician if necessary, and increase the temperature set value. (3) Clean and check the extrusion system and head of the single screw extruder.

What is the importance of single screw extruder temperature control?

Temperature control refers to the temperature of the single screw extruder during plastic extrusion, including the temperature control of the barrel, die and transition body. These temperature controls are related to the viscosity of the material, the sensitivity to temperature, and the aggregation state of the polymer. In general, the temperature of the die head and transition body of single screw extruder is low for medium and low viscosity materials, and the temperature of die head and transition body for high viscosity materials is high, and the fluidity is good.

What is the importance of single screw extruder speed control?

Speed control means that for single screw extrude processing, if the screw speed increases, the shear rate increases. Thermoplastic melts are mostly non-Newtonian pseudoplastic fluids, and their viscosity decreases with the increase of shear rate, and fluidity Increasing the extrusion output also increases. However, if the shear rate is too large, the melt viscosity is too low, which will cause difficulties in the production and operation of single screw extrude. At the same time, the low-viscosity melt will flow backwards under the action of the screw back pressure, and the leakage flow will increase significantly, which will affect the output to a certain extent. , Again, the screw may even slip at high speeds, so the screw speed should be controlled within a certain range. In addition, in the production process of single screw extrude, the screw speed should be kept as stable as possible to avoid fast and slow. Otherwise, it will cause uneven discharge due to excessive changes in the melt viscosity of the material, which will affect normal production.

Nanjing JlEYA is a single screw extruder manufacturer established for more than five years. We work with customers from design to completion to ensure that all technical requirements are met.

Jieya team wish you Merry Christmas and happy new year.

Thanks for old customers trust and support on our twin screw extruders machines. We always keep focusing on the quality and service. And hope to establish business relationship with all new customers. Enjoy your holidays, dear!

The extrusion system of a single screw extruder includes a screw, a cylinder, a funnel, a head, and a nozzle. The plastic is plasticized by the extrusion system into a uniform melt and is continuous under the resulting pressure through the screw of the extruder head.

• What is the relevant information about single screw extruders?

• How to improve the product quality of the single screw extruder?

• What role does the heating and cooling system play in the single screw extruder?

What is the relevant information about single screw extruders?

Each product type in the production line for single screw extruders has its operating characteristics. Only if you know their operating characteristics can you fully measure the efficiency of the machine.

Slug extruder's one of the guys. Record the operating points of single screw extruders and use single screw extruders correctly and sensibly.

The use of a single screw extruder includes several connections such as machine setup, adjustment, test run, operation, maintenance, and repair. Its use has the common characteristics of general machines, mainly in the drive engine and in the speed reduction device.

The working system of the single screw extruder, however, is the extrusion system, which has unique characteristics. When using the single screw extruder, pay particular attention to its properties.

How to improve the product quality of the single screw extruder?

1. About the extrusion product quality of the single screw extruder:

Injection extruders must conform to the raw material formula and process, the product size must correspond to the extrusion equipment and the raw materials must be sufficiently mixed and plasticized to ensure stable extrusion pressure and product quality.

2. Improve extrusion efficiency:

It is related to the selection of the single screw extruder, the screw structure, and the material properties, which are relative and must be considered comprehensively. Simple method, you can choose a larger extruder, the nozzle is opened into a nozzle and several forms.

What role does the heating and cooling system play in the single screw extruder?

The heating and cooling system of the inlet extruder consists of a heating device and a cooling device. It is a necessary condition for the smooth running of the extrusion process. The heater and cooling system shall ensure that the polymer material is melted and plasticized and that the temperature conditions during the molding process meet the process requirement.

The cooling system is generally installed in the cylinder, in the screw, and the bottom of the funnel of the inlet extruder. The cylinder cooling may be water-cooled or air-cooled. In general, small and medium extruder air cooling is used; Large series single screw extruders usually use water cooling or a combination of both. The main use of sludge cooling is a central water cooling system, the purpose of which is to increase the rate of solidification of the material, to stabilize the volume of discharges, and, at the same time, to improve product quality. The cooling system at the bottom of the funnel serves mainly to enhance the conveying effect of solids and to prevent the material particles from sticking due to the increase in temperature, blocking the material opening and impairing the supply. In general, in the case of extruders with screw diameters over 90 mm and fast-running screw extruders, a cooling device shall be installed at the bottom of the funnel.

Nanjing JlEYA has worked for many years to meet every customers’ need for single screw extruder. Just connect them.

underwater pelletizing machine plays an irreplaceable role in the current industrial production process. Only when the underwater pelletizing machine is used correctly can the greatest effect be achieved.

• What problems should be paid attention to when using underwater pelletizing machine?

• What is the cause of the friction clutch failure of the underwater pelletizing machine and its solution?

• How can the underwater pelletizing machine make the pellets cut out by pelletizing have no pores?

What problems should be paid attention to when using underwater pelletizing machine?

1. Pay attention to the temperature change of the underwater pelletizing machine at any time. When touching the sliver with clean hands, the temperature should be raised immediately. Until the sliver touches your hand, it is normal.

2. When the bearing part of the reducer burns, or is accompanied by noise, it should be repaired in time and refueled.

3. When the bearing parts at both ends of the bearing chamber of the underwater pelletizing machine are hot or there is noise, stop the machine for maintenance and add butter. During normal operation, add butter to the bearing chamber every 5-6 days.

4. Pay attention to the operating rules of the underwater pelletizing machine; such as: the machine temperature is high or low, the speed is fast or slow, and it can be dealt with in time according to the situation.

5. When the operation of the underwater pelletizing machine is unstable, pay attention to check whether the gap of the coupling anastomosis is too tight, and adjust it in time to loosen it.

What is the cause of the friction clutch failure of the underwater pelletizing machine and its solution?

Reason analysis: The instantaneous starting voltage of the main motor of the underwater pelletizing machine is too low, the friction disc and the friction disc are overheated, the friction disc and the friction disc are aging, and the air pressure of the friction disc is too low, etc., which can cause the clutch to disengage.

Solution: When starting the main motor of the underwater pelletizing machine, avoid peak power consumption and reduce the feeding load. The minimum restart interval is 30 minutes; in summer, when the main motor is restarted more than twice, it should be extended. Interval time or forced cooling with a fan. Blow with instrument wind and wipe off the dirt on the surface of the friction plate and friction plate with a rag. If the underwater pelletizing machine wears a lot or the surface becomes "vitrified", replace the friction plate and friction plate. Confirm whether the air pressure value can make the friction disc and the friction plate fit together.

How can the underwater pelletizing machine make the pellets cut out by pelletizing have no pores?

One: The different materials used by the underwater pelletizing machine must be separated clearly;

Two: The products produced by the underwater pelletizing machine should be dewatered as much as possible after being crushed and cleaned;

Three: The vent hole on the screw of the underwater pelletizing machine should be unblocked.

Nanjing JlEYA has various underwater pelletizing machines that can provide the increasing of products, and make them more effective, reliable, and consistent.

Zhoushan good quality mini single screw barrel for PVC PP PE ABD plastic extruder machine FOB Price: USD

FLENDER helical gear units for double-screw extruders with parallel drive shafts and the same direction of screw rotation are available in several sizes in the performance range between 200 and 35 000 Nm per shaft and for up to 20 000 kW. They are used mainly in the manufacture of granulates and the refining of raw plastics as well as in the ...

Plastic extruders manufacturer . Bausano is an expert plastic extrusion manufacturer, producing a fully customizable range of plastic extruders for a variety of sizes, applications and materials.. From a lab scale extruder up to industrial production capacity with Single and Twin-screw extruders, we provide every kind of bespoke extruders tailored to your needs.

5.2.1 Single and Twin Screw Extruders. Screw extruders are divided into single screw and multiscrew extruders. Single screw extruders are most popular for their low cost, simple …

Equipment for tailoring plastic material using various additives and fillers to achieve high-performance compound requirements 27 (0)11 483 3015 sales@plastrading Mon - …

Laboratory Scale Twin Screw Plastics Extruder Manufacturers, Factory, Suppliers From China, We are trying to get for in depth cooperation with sincere shoppers, attaining a …

Many products, such as garbage bags and sewage pipes, are suitable for secondary plastic particles for products with low requirements. How to make secondary particles with bright …

The mixer is mainly used for the plastic industry, it used to mix pellet with color masterbatch/pigment for extrusion and pelletizing production. Features of vertical color mixer: 1. Vertical structure with castor wheels, small …