Small Extruder Pelletizing Line- China Suppliers Manufacturers Factory

Jieya team wish you have a nice holiday :)

(Nanjing Jieya is a professional manufacturer of twin screw compounding extruders with 20+ years experience and competitive price. We look forward to receive your inquiry.)

When the single screw extruder is in the extrusion molding process, its extruder screw is divided into 3 sections: feeding section (feeding section), melting section (compression section), metering section (homogenization section), these three sections Correspondingly, three functional areas are composed of materials: solid conveying area, material plasticizing area, and melt conveying area. Each area has different temperature requirements, and specific problems should be analyzed in detail. The temperature of the single screw extruder will be briefly introduced below.

• What is the general temperature of the solid conveying zone in a single screw extruder?

• What is the general temperature in the plasticizing zone of the material in a single screw extruder?

• What is the general temperature of the melt conveying zone in a single screw extruder?

What is the general temperature of the solid conveying zone in a single screw extruder?

The temperature of the barrel in the solid conveying zone of the single screw extruder is generally controlled at 100~1400C. If the feeding temperature is too low, the solid conveying zone will be extended, reducing the length of the plasticizing zone and the melt conveying zone, which will cause poor plasticization of the single screw extruder product and affect product quality.

What is the general temperature in the plasticizing zone of the material in a single screw extruder?

The temperature of the material plasticizing zone in the single screw extruder is controlled at 170~1900C. Controlling the vacuum degree of this section is an important process index. If the vacuum degree is low, it will affect the exhaust effect, resulting in bubbles in the pipe, and seriously reducing the mechanical properties of the pipe. In order to make the gas inside the material easily escape, the plasticization degree of the material in this section should be controlled not to be too high, and the exhaust pipe of the single screw extruder should be cleaned frequently to avoid blockage. The vacuum degree of the barrel is generally 0.08~0.09MPa.

What is the general temperature of the melt conveying zone in a single screw extruder?

The temperature of the melt conveying zone in the single screw extruder should be slightly lower, generally 160~1800C. Increasing the screw speed in this section, reducing the head resistance and increasing the pressure in the plasticizing zone are all conducive to the improvement of the conveying rate. For heat-sensitive plastics such as PVC, the residence time should not be too long in this section. The screw speed is generally 20 ~30r/min. The head of the single screw extruder is an important part of extruded product molding. Its function is to generate a higher melt pressure and make the melt shape into a desired shape. The process parameters of each part of the single screw extruder are: die connector temperature 1650C, die temperature 1700C, 1700C, 1650C, 1800C, 1900C.

This is some information related to the use of single screw extruders. The use of single screw extruders is also closely related to the quality of its products. If you need more information, please contact Nanjing JlEYA.

underwater pelletizing machine is similar to airflow granulator and water jet granulator. The equipment part mainly covers: plastic granulator, single and twin screw plastic extruder, plastic film blowing machine, bag making machine, printing machine, coating machine, Adhesive tape machine, tape slitting machine, slitting machine, strapping machine.

• What is the problem of uneven pelletizing by the underwater pelletizing machine?

• What is the workflow of the underwater pelletizing machine?

• What is the technological advantages of the underwater pelletizing machine?

What is the problem of uneven pelletizing by the underwater pelletizing machine?

1. underwater pelletizing machine, the machine head is not evenly heated, and the machine head temperature is stable before starting up;

2. The cooling water of the underwater pelletizing machine is boiled prematurely, and the water should be boiled when the machine head starts to discharge;

3. It is also possible that there is a problem with the hot runner design of the machine head, which is caused by uneven pressure.

What is the workflow of the underwater pelletizing machine?

Before being made into final products, most polymers must be blended and then pelletized to become marketable raw materials. The power required by the underwater pelletizing machine is directly proportional to the extrusion volume and exponentially related to the size of the filter screen. There are many different types of pelletizer designs, but all pelletizers have some common places, and they can be divided into two categories: cold pelletizing system and die face hot pelletizing system. The main difference between the two categories is the time arrangement of the pelletizing process. The cold pelletizing system cuts pellets from the solidified polymer at the end of the process; while in the die-face hot pelletizing system, pellets are cut when the molten polymer emerges from the die, and pellets are processed downstream cool down.

What are the technological advantages of the underwater pelletizing machine?

The underwater pelletizing machine treated by standard process has the following significant advantages:

1. The appearance standard of the products produced by the underwater pelletizing machine is exquisite and bright;

   
   

2. The hardness of the wear layer in contact with the material by the underwater pelletizing machine can reach HV 600-800, and the local hardness can reach HV900-1100. The hardness is increased to 2-4 times the original hardness. Compared with the non-standard machine without heat treatment, it is resistant to The wear performance is increased by 3-5 times;

3. The products of the underwater pelletizing machine are not deformed after long-term use, effectively avoiding the screw breaking due to the excessive wear of the barrel, and the stable service life is 2-3 times that of the traditional machine, which greatly reduces the investor's investment in replacement parts;

4. The wear-resistant layer of the barrel screw produced by the underwater pelletizing machine has high hardness, while the base material still retains good toughness and processing performance;

5. The service life of the screw of the underwater pelletizing machine has increased from the hundred-ton level of the ordinary plastic pelletizing machine to the thousand-ton level.

Nanjing JlEYA has focused on the production and development of underwater pelletizing machines for several years, and they have always put the needs of customers as their top priority. Here, you can choose the underwater pelletizing machine that suits your need.

The high efficiency of the single-screw extruderis mainly reflected in high output, low energy consumption, and low manufacturing cost. In terms of function, the plastic extruder has been used not only for extrusion molding and mixing processing of polymer materials but its use has been broadened to food, feed, electrode, building materials, packaging, ceramics, and other fields. So how to operate the single screw extruder? The following is a detailed introduction.

 

Here is the content list:

• Preparation work before starting the machine

• Start-up operation

• Stop operation

 

Preparation work before starting the machine

1. For single-screw extruder extrusion production of materials, should meet the required drying requirements, if necessary, further drying.

2. According to the variety of products, size, select the head specifications, the machine will be installed in the order of the column, installed head flange, die body, mouth die, porous plate, and filter network.

3. Connect the compressed air pipe, install the core mold electric heating rod head heating ring, check the water system.

4. Adjust the gap evenly in all parts of the mouth die and check whether the centerline of the main machine and the auxiliary machine are aligned.

5. Start the single-screw extruder of each running equipment, check whether the operation is normal, and find faults in time to eliminate.

6. Turn on the electric heater, the head, body, and auxiliary machine evenly heated up, to be the temperature of each part than the normal production temperature of about 10 degrees, constant temperature of 30 ~ 60 minutes so that the machine temperature inside and outside the same.

 

Start-up operation

Start-up is an important part of the production, poor control will damage the screw and head, the temperature is too high will cause plastic decomposition, the temperature is too low will damage the screw, barrel, and head. The start-up steps are as follows.

1. Start the machine at low speed, idle, check the screw for any abnormalities and motor, amperage meter current no overload phenomenon, the pressure gauge is normal. Machine idling should not be too long to prevent the screw and barrel-scraping grinding.

2. Gradually add a small amount of material, wait for the material extrusion out of the die, before the normal addition of material. Before the plastic is extruded, no one should be in front of the mouth die to prevent casualties.

3. After the plastic is extruded, it is necessary to lead the extruded material slowly on the cooling and shaping, traction equipment, and start this equipment beforehand. Then, according to the control instrument indication value and the requirements of the extruded products, each link will be properly adjusted until the extrusion operation reaches the normal state.

4. Cutting and sampling, checking whether the appearance meets the requirements, whether the size meets the standard, quickly testing the performance, and then adjusting the extrusion process according to the requirements of quality, so that the products meet the standard requirements.

 

Stop operation

1. Stop feeding, extrude the plastic in the single screw extruder and turn off the power of the barrel and head for the next operation.

2. Shut off the power of the main machine and the auxiliary machines at the same time.

3. Open the head connection flange, clean the porous plate and various parts of the head, when cleaning, should use copper rods, copper pieces, after cleaning, apply a little oil. Screw, barrel clean up, if necessary, the screw from the end of the machine out of the top, clean up after recovery, in general, available for the transition of material cleanup.

4. Extrusion of polyolefin plastics, usually in the extruder full load shutdown (with material shutdown), when the air should be prevented from entering the barrel, so as not to oxidize the material and affect the quality of the product when continuing production. For polyvinyl chloride plastics, can also stop with material, then close the material door, reduce the temperature at the head connection body (flange) 10 ~ 20 degrees, to stop the machine after the material squeeze net.

5. Close the total power and cooling water main valve.

 

If you still have questions, you can consult our company. Our company's website is https://www.njjyextrusion.com/

 

 

The twin screw extrudernot only has the characteristics of a single-screw extruder, but also has the advantages of convenient feeding, stable extrusion, and convenient exhaust. It is widely used in the production and processing of extruded products.

Why are twin screw extruders warmly welcomed now?

Choose a single-screw extruder or a twin screw extruder?

What are the technical points of the twin screw extruder?

Why are twin screw extruders warmly welcomed now?

The twin screw extruder can not only add more ingredients to the company's products, but also can choose to quickly complete the manufacturing. Considering that "new crown pneumonia" has put every industry into trouble, the market has been looking for a quick turnaround to pay for healthy food. In addition, you may need to make up for the loss of production and sales or increase production and sales based on the current situation. Twin-screw extension can help you, and considering the lower cost and higher production and sales, it can bring more profits.

Choose a single-screw extruder or a twin screw extruder?

The single-screw extruder is used for extrusion processing technology and equipment, and the particle raw materials stay in the extruder for a long time. This means that a single-screw extruder requires a longer period than a twin screw extruder to produce the products required by the enterprise. In addition, the twin screw extruder allows you to better control the complex operation process and actual operation. As everyone knows, these controls are much more complicated. This is very important for foods that need to be mixed and mixed. The production and manufacturing facilities are complete, and the actual effect of twin-screw extrusion is the best. For polymer materials, twin-screw extrusion is also particularly effective. Considering that the design concept of twin screw extruder has a relatively large flexibility, it can be used in many industries for very specific operation processes.

What are the technical points of the twin screw extruder?

In the extrusion process of the twin screw extruder, the material is transformed from the glass state to the molten state. In addition to the balance between the heat required for plasticization of the material and the amount of heat supplied, the material is melted. Pressure is also a very important control indicator. Because the material is affected by the compression ratio of each section of the die resistance screw during the extrusion process, it does not exist under normal pressure. For different die, the compression ratio of each section of the screw is basically constant and immutable. Under the premise of the same extrusion speed, increase or decrease the feed rate, the volume of the screw material in the feeding section will change, and the volume of the material in the exhaust section will remain unchanged, so the compression section of the feeding section changes with the compression ratio, and its melt pressure follows Increase or decrease; under the premise of the same feed rate, increase or decrease the extrusion rate, the volume of the screw material in the feeding section will also change. The volume of the material in the exhaust section remains unchanged, so the compression section of the feed section changes with the compression ratio, and its melt pressure increases or decreases accordingly; the feed speed increases or decreases simultaneously with the extrusion speed, because the volume of the screw material in the feed section remains unchanged , Only due to the increase or decrease of the speed, the melt pressure change.

Due to different fields and different types of twin screw extruder, they are widely used in many industries. To meet these growing demands, Nanjing JlEYA has committed to providing the increasing of twin screw extruder.

PVC compounding extruder is divided into two types of hard and soft RPVC pipes, RPVC pipes are chemically resistant and insulating, mainly transporting various fluids and used as wire sleeves, etc. SPVC pipes are manufactured by extruding PVC resin with a large amount of plasticizer and a certain amount of stabilizer and other additives after granulation. The following is a detailed description of the equipment functions of the PVC compounding extruder.

 

Here is the content list:

• High Speed Mixer High-Speed Mixing

• Accurate matching of feeding device

• Water tank for pipe forming

• Traction machine frequency conversion speed control

• Automatic cutting

• Unloading the material from the turning frame

 

High Speed Mixer High-Speed Mixing

Raw material intermixture is to feature PVC stabilizer, softener, inhibitor, and different auxiliary materials to the high-speed mixer in proportion and sequence to the method.

Accurate matching of feeding device

The PVC compounding extruder part is equipped with a quantitative feeding device to match the extrusion volume with the feeding volume to ensure stable extrusion of products. Due to the characteristics of the conical screw, the feeding section has a larger diameter, and the heat transfer area and sheer speed of the material are larger, which is contributive to the plasticization of the fabric and also the little diameter of the screw within the metering section reduces the warmth transfer space and also the sheer speed of the soften so that the melt can be extruded at a lower temperature. When the screw rotates in the barrel, the PVC mixture is plasticized and pushed to the head to achieve compaction, melting, mixing, and homogenization and to achieve the purpose of exhaust and dehydration. The feeding device and screw drive device adopt frequency conversion to realize synchronous speed regulation.

PVC compounding extruder dies head part of the compacted, molten, blended, and homogenized PVC has subsequent materials through the screw to the die head extrusion die head is the key component of pipe forming.

Water tank for pipe forming

The vacuum shaping water tank of PVC compounding extruderis used for pipe shaping and cooling, the vacuum shaping water tank is equipped with vacuum system for shaping and cooling and water circulation system stainless steel box body circulating water spray cooling, the vacuum shaping water tank is equipped with front and rear moving device and left and right, high and low adjustment manual device.

Traction machine frequency conversion speed control

The traction machine is used to continuously and automatically lead the cooled and hardened pipe from the head with frequency control.

Automatic cutting

The cutting machine is controlled by the travel switch according to the required length and then automatically cut and delay the turning frame to implement the flow of production, the cutting machine with a fixed-length work switch signal as a command to complete the whole process of cutting in the cutting process and pipe running synchronization cutting process is completed by electric and pneumatic drive, the cutting machine is equipped with a dust suction device to suck out the cutting debris and recycling.

 

Unloading the material from the turning frame

The material turning action is controlled by the cylinder through the air circuit to achieve the material turning frame is equipped with a limit device when the cutting saw cut off the pipe after the pipe continues to transport after a delay, the cylinder into the work of turning action to achieve the purpose of unloading. After unloading, it will be automatically reset after a delay of several seconds to wait for the next cycle.

 

Nanjing JlEYA is the leading manufacturer extruder manufacturer specializing in twin screw extruder, mini twin screw extruder, plastic extruder and parallel twin screw extruder in China, which is widely used in compounding, modification, polymerization, devolatilization, reaction, recycling, etc. After 17 years development, now we have 20,000 square meters workshop with annual sales over 300+ sets, export over 60 countries.

JIEYA has the most experienced technical core team, with extensive experience in system integration of the development manufacturing, materials processing, application technology andother fields.

In terms of the principle of motion, there are different types of twin-screw extruderswith isotropic and anisotropic meshing and non-meshing types. So what are the types of twin-screw extruders? And what are the application areas? The following is a detailed introduction.

 

Here is the content list:

l Isotropic twin-screw extruder

l Anisotropic twin-screw extruder

l Non-Engaging Twin-Screw Extruders

l SHJ-20 twin-screw laboratory extruder

l Application areas

 

Isotropic twin-screw extruder

These extruders are available at low and high speeds, the former mainly for profile extrusion, while the latter is used for special polymer processing operations.

(1) Close-meshing extruder. Low-speed extruders have a closely meshed screw geometry, where the profile of one screw is closely matched to the profile of the other screw, i.e., a conjugate screw profile.

(2) Self-cleaning extruder. High-speed co-rotating extruders have a closely matched screw-prong profile. This screw can be designed to have a fairly small screw gap so that the screw has a closed self-cleaning effect, this twin-screw extruder is called a tight self-cleaning co-rotating twin-screw extruder.

 

Anisotropic twin-screw extruder

The tightly meshed anisotropic twin-screw extruder has a small gap between the two screw grooves (much smaller than that in a co-engaged twin-screw extruder) so that a positive conveying characteristic can be achieved.

 

Non-Engaging Twin-Screw Extruders

The center distance between the two screws of a non-engaging twin-screw extruder is greater than the sum of the radii of the two screws.

 

SHJ-20 twin-screw laboratory extruder

It is suitable for universities, colleges, and scientific research laboratories for process and formula development, etc. It has the features of beautiful appearance, compact structure, easy to use and maintain, and precise control of process conditions. Gearbox homemade torque level: T/A3≤8 national standard main parts, twin-screw extruder new structure design, and hardened gear teeth of high precision grinding, to ensure that the gearbox works efficiently for a long time. Screw self-made: Screw elements with tightly meshed design, block type, can be easily replaced to suit different materials. Barrel captive: The precision grade of the twin-screw extruder can reach T6， favorable to energy saving, and the block type design makes various combinations possible.

 

Application areas

The two main areas of application of twin-screw extruders are extrusion of thermosensitive materials such as PVC pipes and profiles and processing of special polymers such as blending, venting, chemical reactions, etc. Twin-screw extruders for profile extrusion have intermeshing screw ribs and grooves and operate at a low speed of about 10/min or less. Compared to single screws, twin-screw extruders have much better feeding and conveying performance, especially for those difficult to feed and easy to slip, such as fibrous, powdery, and greasy materials. The short and uniform material retention time, better mixing, and larger heat transfer area allow for good material temperature control, which is especially important for processing heat-sensitive materials.

 

If you want to buy a twin-screw extruder, you can consider our cost-effective products.

Nanjing JlEYA is the leading manufacturer extruder manufacturer specializing in a twin-screw extruder, mini twin screw extruder, plastic extruder, and parallel twin-screw extruder in China, which is widely used in compounding, modification, polymerization, devolatilization, reaction, recycling, After 17 years of development, now we have 20,000 square meters workshop with annual sales over 300+ sets, export over 60 countries.

Nanjing Team sincerely invite you to attend The 15th China Chongqing Rubber, Plastics Industry Exhibition.

Our booth no.: S2544

Time: May 27-30, 2021

Address: Chongqing International Expo Center 

Wish to meet you at there ;)

TENGDA buy plastic extruder We, as a professional buy plastic extruder manufacturer, have been focusing on improving ourselves to offer customers satisfying service. For example, customization service, reliable shipping service and efficient after-sales service can all be offered at TENGDA Extruder Machine Manufacturers .vinyl extrusion,plastic ...

co rotation parallel twin screw extruder manufacturer/supplier, China co rotation parallel twin screw extruder manufacturer

We are also specializing in improving the things management and QC method in order that we could retain terrific edge inside the fiercely-competitive small business for Filling …

YILI MACHINERY Co., Ltd. YILI MACHINERY is founded in 1991, We are the top leading plastic machinery manufacturer in China. We have THREE main business sections： Plastic Extrusion machinery which includes High efficiency/Energy-saving European standard PE/PP/PPR/PVC pipe extrusion line, large diameter PE/PP double wall corrugated pipe ...

Double Screw Extruder Hot Selling Compound Twin Screw Extruders Plastic Extruder Machine Twin Screw,Twin Screw Extruder, Plastic Extruder Machine についての詳細を検索 Double Screw Extruder Hot Selling Compound Twin Screw Extruders Plastic Extruder

80kg/hr Underwater Pelletizing System For Laboratory And Small Scale ProductionContact Now. CHT30-Eco-UW10 Under Water Pelletizizing system for laboratory and small scale production with capacity of max.80kg/hr Technical specification No. Denomination of the delivery Qty. 1.0 Raw materials dealing ... Read More. 2020-05-26 17:40:08.

Pragati Extrusion India Private Limited - Offering 50 Hz Two Stage Plastic Extruder Machine, For Industrial at Rs 2200000/unit in Rajkot, Gujarat. Also find Plastic Extrusion Machines price list

Strands 20-63 With Conic Twin Screw Extruder ZS55/120 Output 220kg/H Pvc Pipe Machine Special features: It can be equipped with ZS51/110 extruder output 200kg/h or it can be equipped with 65/132 high output 350kg/h for optional Siemens PLC controls the entire production line, HYPET software, and high configuration Bimetal barrel screw.....