








Material delivery method
In a single-screw extruder, there is friction drag in the solids conveying section and viscous drag in the melt conveying section. The friction properties of the solid material and the viscosity of the molten material determine the conveying behavior. If some materials have poor friction properties, if the feeding problem is not solved, it will be difficult to feed the materials into the single-screw extruder. In twin-screw extruders, especially intermeshing twin-screw extruders, the conveying of materials is to some extent forward displacement transmission, and the degree of forward displacement depends on the relationship between the flight of one screw and that of the other screw. the proximity of the relative screw grooves. The screw geometry of the closely intermeshing counter-rotating extruder results in a high degree of positive displacement delivery characteristics.
Material flow velocity field
At present, the flow velocity distribution of the material in the single-screw extruder has been described quite clearly, while the flow velocity distribution of the material in the twin-screw extruder is quite complicated and difficult to describe. Many researchers just do not consider the material flow in the meshing area to analyze the flow velocity field of the material, but these analysis results are very different from the actual situation. Because the mixing characteristics and overall behavior of a twin-screw extruder are primarily determined by the leakage flow that occurs in the intermeshing zone, the flow situation in the intermeshing zone is quite complex. The complex flow spectrum of the material in the twin-screw extruder shows macroscopic advantages that the single-screw extruder cannot match, such as sufficient mixing, good heat transfer, large melting capacity, strong exhaust capacity and good temperature control of the material, etc.
The twin screw extrudernot only has the characteristics of a single-screw extruder, but also has the advantages of convenient feeding, stable extrusion, and convenient exhaust. It is widely used in the production and processing of extruded products.
Why are twin screw extruders warmly welcomed now?
Choose a single-screw extruder or a twin screw extruder?
What are the technical points of the twin screw extruder?
Why are twin screw extruders warmly welcomed now?
The twin screw extruder can not only add more ingredients to the company's products, but also can choose to quickly complete the manufacturing. Considering that "new crown pneumonia" has put every industry into trouble, the market has been looking for a quick turnaround to pay for healthy food. In addition, you may need to make up for the loss of production and sales or increase production and sales based on the current situation. Twin-screw extension can help you, and considering the lower cost and higher production and sales, it can bring more profits.
Choose a single-screw extruder or a twin screw extruder?
The single-screw extruder is used for extrusion processing technology and equipment, and the particle raw materials stay in the extruder for a long time. This means that a single-screw extruder requires a longer period than a twin screw extruder to produce the products required by the enterprise. In addition, the twin screw extruder allows you to better control the complex operation process and actual operation. As everyone knows, these controls are much more complicated. This is very important for foods that need to be mixed and mixed. The production and manufacturing facilities are complete, and the actual effect of twin-screw extrusion is the best. For polymer materials, twin-screw extrusion is also particularly effective. Considering that the design concept of twin screw extruder has a relatively large flexibility, it can be used in many industries for very specific operation processes.
What are the technical points of the twin screw extruder?
In the extrusion process of the twin screw extruder, the material is transformed from the glass state to the molten state. In addition to the balance between the heat required for plasticization of the material and the amount of heat supplied, the material is melted. Pressure is also a very important control indicator. Because the material is affected by the compression ratio of each section of the die resistance screw during the extrusion process, it does not exist under normal pressure. For different die, the compression ratio of each section of the screw is basically constant and immutable. Under the premise of the same extrusion speed, increase or decrease the feed rate, the volume of the screw material in the feeding section will change, and the volume of the material in the exhaust section will remain unchanged, so the compression section of the feeding section changes with the compression ratio, and its melt pressure follows Increase or decrease; under the premise of the same feed rate, increase or decrease the extrusion rate, the volume of the screw material in the feeding section will also change. The volume of the material in the exhaust section remains unchanged, so the compression section of the feed section changes with the compression ratio, and its melt pressure increases or decreases accordingly; the feed speed increases or decreases simultaneously with the extrusion speed, because the volume of the screw material in the feed section remains unchanged , Only due to the increase or decrease of the speed, the melt pressure change.
Due to different fields and different types of twin screw extruder, they are widely used in many industries. To meet these growing demands, Nanjing JlEYA has committed to providing the increasing of twin screw extruder.
The composition of the single screw extruder: mainly consists of servo motor, reduction box, screw cylinder, nozzle head, filter air, heating and cooling system, touch screen, and SPS control. It is the extrusion host to form.
What are the reasons why the main engine of the single screw extruder cannot be started and the solutions?
What are the reasons and solutions for the high inlet flow of the single screw extruder?
What is the design concept of the single screw extruder?
1. Reasons:
(1) The driving program of the single screw extruder is wrong.
(2) There is a problem with the main engine thread and whether the fuse is blown.
(3) The locking device for the single screw extruder and the main engine works.
2. Treatment:
(1) Check the program of the insert extruder and restart in the correct order.
(2) Check the main engine circuit.
(3) Check whether the lubricating oil pump has started and check the status of the locking device concerning the main engine. The oil pump cannot be turned on and the engine cannot be turned on.
(4) The inverter has not discharged the induction current, turn off the main power supply and wait five minutes before starting.
(5) Check if the emergency button of the single screw extruder has been reset.
1. Reasons: (1) The single screw extruder has an insufficient heating time and a large torque. (2) A certain section of the heating does not work.
2. Treatment method: (1) Use the handwheel when driving the single screw extruder. If it is not easy, extend the heating time or check that the heaters of the individual sections work properly.
The main engine makes an abnormal noise:
1. Reasons: (1) Main engine stock damaged. (2) A specific SCR in the SCR DC power supply of the main engine is damaged.
2. Treatment method: (1) Replace the main engine stock of the single screw extruder. (2) Check the thyristor alignment and replace the thyristor component if necessary.
1. High-speed and high-Yield extrusion based on high quality.
2. The design concept of low-temperature plasticization ensures the extrusion of high-quality products.
3. The two-stage overall design of the single screw extruder reinforces the plasticization function to ensure the adjustment of the high-performance extrusion.
4. Special barrier, comprehensive mixing design to ensure the mixing effect of materials.
5. High torque drop, extra-large pressure bearing.
6. Gears and shafts are made of high-strength alloy steel, cooled, and chipped.
7. High hardness, high finish, extremely quiet.
8. PLC-intelligent control can realize the connection between main and auxiliary machines.
9. The easy-to-monitor human-machine interface makes it easy to understand the processing and machine status.
10. The control method (temperature device) can be changed if necessary.
11. The material is 38CrMoAL/A nitric treatment, wear-resistant.
12 Strict temperature control accuracy, combined with air cooling and water cooling.
13. The single screw extruder has a unique inlet design and complete water cooling.
14. An single screw extruder with a grooved surface of the lower shell has an improved feed function that guarantees a high speed and a high yield of extrusion.
The single screw extruder is increasingly used in industrial production.Nanjing JlEYA has committed itself to offering the best-suited single screw extruders at a reasonable price, and all that is necessary to meet the needs of the customer.
Each type of product in the plastic extruder line has its operating characteristics, and a detailed understanding of its operating characteristics is necessary to give full play to the effectiveness of the machine. The following is a detailed description of the operating procedures and maintenance methods for plastic extruders.
Here is the content list:
Operation procedures
Maintenance methods
The plastic extruder is one of the machine types, master the extruder operation points, the correct and reasonable use of a plastic extruder. The use of plastic screw extruder includes a series of links such as installation, adjustment, commissioning, operation, maintenance, and repair of the machine, and its use has the commonality of general machines, mainly in the drive motor and reduction and speed change device. However, the working system of the plastic screw extruder, the extrusion system, is unique, and special attention should be paid to its characteristics when using the plastic screw extruder. Extruder manuals generally have clear provisions for the installation, adjustment, and commissioning of the machine, here the main points of the operation, maintenance, and repair of the plastic screw extruder are briefly described as follows: in particular, to correctly grasp the structural characteristics of the screw, heating and cooling management instrumentation characteristics and assembly, the correct extrusion process conditions, the correct operation of the machine.
1.Pastic extruder equipment should be placed in a ventilated position to ensure that the heat of the motor work prolongs its life; the machine should be kept well grounded.
⒉Regularly check the tool screws, the plastic extruder after 1 hour of use, with tools to tighten the moving knife, fixed knife screws, to strengthen the fixed between the blade and the knife frame; should be regularly filled with lubricating oil to ensure the lubrication between the bearings; to ensure the sharpness of the cutting edge of the tool, should always check the tool to ensure its sharpness, to reduce unnecessary damage to other parts caused by the blunt lack of the blade; regularly check whether the belt is loose, and timely tightening.
3. Restart - Before starting the plastic extruder for the second time, the remaining debris in the machine chamber should be cleared to reduce the starting resistance. Periodically open the inertia cover and pulley cover to clear the ash outlet under the flange, which can cause the powder to enter the shaft bearing.
4. Replacement parts - When replacing knives, the clearance between the moving and fixed knives should be 0.8 MM for crushers over 20 HP and 0.5 MM for crushers under 20 HP. The thinner the recycled material is, the gap can be adjusted appropriately larger.
If you need to know more, you can consult our company. The company focused on co-rotating twin-screw compounding extruders with the core of the various R&D and manufacturing, such as a twin-screw extruder, mini twin screw extruder, plastic extruder, parallel twin-screw extruder, and so on, the application covers compounding mixing modified granulation, polymerization, devolatilization, step molding, renewable recycling, and other fields.
Today, we loaded 2x40HQ export to Vietnam.
One is SHJ-50 twin screw extruder, the other is SHJ-72 twin screw extruders. Both extruders are used for making filler masterbatch.
Nanjing Jieya is a leading manufacturer of twin screw compounding extruders with over 20 years experience. We will offer you the top quality with best price.
We warmly welcome your inquiry.
The engineering plastic twin screw extruder consists of a transmission device, a feed device, a barrel, and a screw. The function of each component is similar to that of a single-screw extruder. The difference to the single screw extruder is that in the engineering plastic twin screw extruder two parallel snails are arranged in the "cross-section" of the material.
What is the working principle of the engineering plastic twin screw extruder?
How do you treat a engineering plastic twin screw extruder?
Why is the cooling device particularly important when using engineering plastic twin screw extruders?
From the point of view of the principle of movement, the engineering plastic twin screw extruder distinguishes between the straight and uneven, and non-foaming types.
1. Double screw extruder of technical plastic
This type of engineering plastic twin screw extruder has a low speed and a high speed. The former is mainly used for profile extraction, while the latter is used for special polymer processing operations.
(1) Tightly machined extruder. The slow-running extruder has a closely combining screw geometry, in which the spiral antenna shape of one snail closely matches the spiral antenna shape of the other snail, i.e. the conjugated snail shape.
(2) Self-cleaning extruder. The simultaneous high-speed extruder has a closely tuned spiral shape. This type of snail can be executed with a relatively small snail split so that the snail has a closed self-cleaning effect. This type of engineering plastic twin screw extruder is called a compact self-cleaning engineering plastic twin screw extruder.
The gap between the two screw edges of the closely combining, opposing engineering plastic twin screw extruder is very small (much smaller than the gap in the evenly rotating engineering plastic twin screw extruder) so those positive conveying properties can be achieved.
2. Non-reciprocating double screw extruder of technical plastic
The axis distance between the two snails of the non-foaming engineering plastic twin screw extruder is greater than the sum of the radii of the two snails.
1. After using the engineering plastic twin screw extruder for 500 hours, iron chips or other impurities from the gears are in the gearbox. Therefore, the gears should be cleaned and the gear lubricant replaced.
2. The engineering plastic twin screw extruder should carry out a comprehensive inspection of the extruder after an operating period to check the density of all snails.
3. If the double screw extruder is suddenly switched off during production, the main drive, and the heating stops, if the power supply is restored, each section of the cylinder shall be reheated to the specified temperature and kept for a specified period, before you can start the extruder.
4. If the display and the display of the engineering plastic twin screw extruder are full, check if the contact of the thermocouple, etc. is good.
After the molded plastic extrusion layer has left the engineering plastic twin screw extruder, it should be cooled and formed immediately, otherwise, it will deform under the influence of gravity. The cooling method normally uses water cooling and is divided into quick cooling and slow cooling according to the different water temperatures. Fast cooling is the direct cooling by cold water. Rapid cooling is advantageous for the design of the extruded plastic layer, but in the case of crystalline polymers, due to sudden heat cooling, it is easy to leave internal stresses in the extruded layer structure, which leads to cracks during use. Generally PVC The plastic layer is deterred. Slow cooling should reduce the inner tension of the product. Water with different temperatures is given in the cooling water tank to gradually reduce the temperature and shape of the product. The extrusion of PE and PP takes place under slow cooling, i.e. through hot water, hot water, and cold water, which is called three-stage cooling.
Nanjing JlEYA is the leading manufacturer extruder manufacturer specializing in twin screw extrude. If you want to get more information, just go and connect them.
As common extruder equipment used in the plastic processing industry, single screw extruder is mainly used for extruding soft and hard PVC, polyethylene, and other thermoplastics, which can process many kinds of plastic products, such as blown film, extruded pipe, pressboard, drawn ribbon, etc. It can also be used for melt pelletizing. The plastic extruder has advanced design, high quality, good plasticization, low energy consumption, involute gear transmission, low noise, smooth operation, high load capacity, and long life. To have a long service life of the machine, maintenance measures are indispensable, the following is a detailed description of the single-screw extruder maintenance measures.
Here is the content list:
Daily maintenance.
Regular maintenance.
1. Because the electrical control system of single-screw extruder has high requirements for ambient temperature and dustproof, the electrical system should be separated from the production site, and install ventilation or ventilation fan, it is recommended that the electrical control cabinet in a simple room, keep the room clean, ventilation, so that the indoor temperature is not higher than 40 ℃.
2. Single-screw extruderis not allowed to run empty, so as not to roll the screw and machine simple hair. Host start idling is not allowed to exceed 100r / min; start the host first low speed, after starting the host to check for abnormal noises and then slowly increase the host speed to within the allowable range of the process (can be adjusted to the best state is good). When the new machine is breaking in, the current load should be at 60-70%, and the current in normal use should preferably not exceed 90%. Note: If an abnormal sound occurs when the extruder is running, it should be stopped immediately for inspection or repair.
3. Turn on the oil pump first and turn off the oil pump after shutting down the machine; keep the water pump working during the whole production process and do not stop the pump to avoid the barrel temperature rising and causing the material in the barrel to decompose and carbonize; the asbestos wind cover of the main motor fan needs to be cleaned often to avoid the dust sticking too much to block the wind cover and cause the motor to overheat and trip due to insufficient heat dissipation.
4. Clean up the dust and dirt, tools, and debris on the surface of the unit in time.
1.Regularly check the screws and other fasteners on the surface of the single-screw extruder unit for looseness and timely and proper tightening. The lubricant level of the transmission box should be added or replaced promptly (the dirt at the bottom of the oil tank should be cleaned regularly). For new machines generally, 3 months to replace the oil, after that every six months to a year. The oil filter and oil suction pipe should be cleaned regularly (once a month).
2. Single screw extruder gearbox maintenance and general standard reducer are the same. The main thing is to check the wear and failure of gears and bearings.
3, When reinstallation please note that A, B two screws must be in the original position, can not be replaced! After the installation of the new combination of the screw on the machine, you must first use the hand pan car, such as normal rotation before the low-speed start. Screw or barrel for a long time without use, there should be anti-rust and anti-fouling measures, the screw should be placed hanging. If the threaded block is with fire, the flame should be moved left and right, while burning to clean up, and can not burn too much (blue ringers red), not to mention the thread block into the water.
4. Regularly calibrate the temperature control instrument to check the correctness of its adjustment and the sensitivity of its control.
5. In the barrel with a cooling water tank, must be used distilled water to prevent the formation of scale blocking the cooling water channel in the barrel, resulting in temperature failure. Pay attention to the appropriate amount of water in use to prevent scaling. If the blockage should be changed down the cylinder specific maintenance, no blockage and the water output is small indicates that there is scale, the tank water should be changed to dilute hydrochloric acid swishing cycle, clear scale to normal and then change the distilled water. General water in the tank is used to cool the barrel, and the natural water we pass is used to cool the tank. Regularly check the water quality of the cooling water tank, if there is turbidity, should be replaced promptly.
6.Check whether the solenoid valve is working properly, the coil has not burned out if there is a timely replacement.
7. The temperature does not rise to quite the temperature continues to rise and fall may exist for the following reasons: whether the day electric couples loose fall; heater relay is working properly; solenoid valve is working properly, timely replacement of deformation of the heater, and tighten the screws.
8. Timely clean up the dirt in the vacuum tank, and the material in the exhaust chamber so that the pipeline is smooth. Vacuum pump seals need to be replaced promptly if there is wear and tear regular inspection, the output shaft jumping is bearing damage and shaft fracture must be opened and replaced, such as the gearbox two output shaft bearing position wear is too serious, the box must be replaced to avoid greater loss of failure.
9, To drive the screw rotation of the DC motor to focus on checking the brush wear and contact, the insulation resistance value of the motor whether in the specified value should also be measured frequently. In addition, check the connection line and other components that are rusted, and the use of protective measures.
10. When the single-screw extruder needs to stop using for a long time, should be in the screw, Jane, the head, and other working surfaces coated with anti-rust grease. The small screw should be suspended in the air or placed in a special wooden box, and a wooden block pad flat, so as not to deform the screw or bruise.
11. Single-screw extruder attached to the cooling water pipe wall is prone to scale external corrosion and rust. Maintenance should be carefully checked, too much scale will block the pipeline, can not achieve the cooling effect, rust will be serious leaks, so maintenance must take descaling and anti-corrosion cooling measures.
12. Designate a person responsible for the maintenance of equipment. And each maintenance and repair detailed record is included in the plant equipment management files.
If you still have questions, you can consult our company, we are happy to answer for you. The company insists on the purpose of "quality first, customer first", and warmly welcomes new and old customers to cooperate with us.
PVC compounding extruder is divided into RPVC pipe and SPVC pipe, RPVC pipe is easy to cut, welding, bonding, heating can be bent and therefore very easy to install and use. SPVC pipe has excellent chemical stability excellent electrical insulation and good flexibility and colorability this pipe is often used to replace rubber pipe to transport liquid and corrosive media also used as cable casing and wire insulation pipe, etc. So how do choose raw materials and the operation of PVC compounding extruder? The following is a detailed introduction
Here is the content list:
Raw material selection
Safety operating procedures
PVC compounding extruder in the production of hard pipe resin should be selected from the lower polymerization degree of SG-5 resin polymerization degree of the higher its physical and mechanical properties and heat resistance is better, but the resin liquidity is poor to bring some difficulties in processing, so generally choose viscosity of 1.7 ~ 1.8 × 10-3Pa-s SG-5 resin is appropriate. Hard pipe generally uses lead-based stabilizers whose thermal stability is good commonly used trisodium lead but its lubricity is poor usually and good lubricity of lead, barium soap type and use. Processing hard tube lubricant selection and use are very important to consider both internal lubrication to reduce intermolecular forces to reduce the viscosity of the melt are conducive to molding and to consider external lubrication to prevent the melt and hot metal adhesion to make the product surface shiny. Internal lubrication is generally used metal soap type external lubrication with low melting point wax. Filler mainly with calcium carbonate and barium barite powder calcium carbonate to make the pipe surface performance of good barium can improve the molding of the pipe easy to shape both can reduce costs but the amount of too much will affect the performance of the pipe pressure pipe and corrosion-resistant pipe is best not to add or add less filler.
1. Personnel without induction test and operation training cannot operate the extruder independently.
2. People who have poor eyesight and slow response can not be on duty to operate.
3. Before starting the machine to do a good job of environmental health around the PVC compounding extruder equipment, equipment around the pile of items not related to production.
4. Check the safety settings of the extruder before production for damage and test whether it can work effectively. Check whether the connection bolts are loose and whether the safety guards are firm.
5. Check the lubrication parts, remove the dirt, and refill the lubricant.
6. PVC compounding extruder barrel and die heating constant temperature time to ensure that the material temperature does not reach the process requirements when driving production.
7. Before starting the screw drive motor to use the hand plate support V pulley, should be flexible rotation, no blocking phenomenon; then start the lubricating oil pump work 3min before starting the screw rotation at low speed.
8. Screw airlift time should not exceed 2 ~ 3min.
9. PVC compounding extruder barrel before adding material to check the barrel, hopper, there is no foreign matter; raw materials should be free of metal, sand, and other impurities to Prevent damage to the screw.
10. The screw starts, the transmission parts work sound normal, the main motor current within the allowable rated value, before allowing the barrel to add material, adding material should first be a small amount of evenly added material.
11. When adjusting the die gap or clearing the dirty material, the operator should wear gloves and not face the barrel and die to prevent the molten material from spraying out of the die and scalding the body.
12. Extruder driving operation is not allowed to repair, and no one is allowed to do any work on the equipment at this time.
13. In case of the following phenomena, should be an emergency stop.
Bearing parts of the high temperature, lubricating oil (grease) out; motor odor, smoke, or shell temperature is too high; speed box lubricating oil temperature, smoke; transmission parts emit irregular abnormal sound; machine work produces violent vibration; screw suddenly stop rotating.
14. PVC compounding extruder equipment on the safety cover and the location of the safety alarm device is not allowed to change at will, not to mention artificially caused by the malfunction.
15. Find that the equipment leakage, oil leakage phenomenon should be timely maintenance troubleshooting, no water, oil flow around the machine.
If you have questions about how to use the PVC composite extruder, you can contact us on the official website. We are happy to answer for you.
The basic mechanism of the twin screw extrusion process is simply that a screw rotates in the barrel and pushes the plastic forward. The screw structure is a bevel or ramp wrapped around a central layer, the purpose of which is to increase the pressure to overcome the higher resistance. What do I need to pay attention to when using a twin screw extruder? The following is a detailed description.
Here is the content list:
l Structural principles
l Temperature principles
l Speed reduction principle
For the extruder, there are three kinds of resistance to overcome when working: one is friction, which contains the friction of the solid particles (feed) on the barrel wall and the mutual friction between them during the first few turns of the screw (feed area); the second is the adhesion of the melt on the barrel wall, and the third is the resistance of the internal logistics of the melt when it is pushed forward.
According to Newton's theorem, if an object is at rest in a certain direction, then the object is in a state of equilibrium balance of forces in this direction. For the circumferential movement of the screw, it is no axial motion, that is, the axial force on the screw is in equilibrium. So if the screw exerts a large forward thrust on the plastic melt, it also exerts a backward thrust on another object of the same magnitude but in the same direction. The thrust is exerted on the thrust bearing behind the feed opening. Most single screws have right hand threads, and if viewed from the back, they rotate backward, and they spin backward out of the barrel by rotational motion. In some twin screw extruders, however, the two screws rotate backward and cross each other in both barrels, so one must be right handed and one left handed, and in the case of an occluding twin screw, both screws rotate in the same direction and must therefore have the same orientation. However, in either case, there are thrust bearings that withstand backward forces and still comply with Newton's theorem.
Plastics extruded by twin screw extruders are thermoplastics, which melt when heated and solidify again when cooled. Thus, heat is needed during the extrusion process to ensure that the plastic can reach the melting temperature. So where does the heat to melt the plastic come from? First of all, the pound feed preheat and barrel/die heaters may play a role and are very important at startup. In addition, the motor feed energy, the frictional heat generated in the barrel as the motor overcomes the resistance of the viscous melt and turns the screw, is the most important heat source for all plastics, except for small systems, low speed screws, high melt temperature plastics, and extrusion coating applications. In operation, it is important to recognize that the barrel heater is not the primary heat source and that it may play a smaller role in extrusion than we might expect. The post barrel temperature is more important because it affects the rate of solids transport in the dentition or feed. In general, except for a specific purpose (such as varnishing, fluid distribution, or pressure control), the die head and die temperature should be at or near the temperature required for the melt.
In most twin screw extruders, the screw speed is varied by adjusting the motor speed. The drive motor usually turns at a full speed of about 1750 rpm, which is too fast for an extruder screw. If it turns at such a fast speed, too much frictional heat is generated and a uniform, the well mixed melt cannot be prepared because the retention time of the plastic is too short. A typical speed reduction ratio should be between 10:1 and 20:1, with either a gear or pulley set for the first stage, but with a gear and a screw positioned in the center of the last large gear for the second stage. For some slow running machines (eg. twin screws for UPVC), there may be three reduction stages and the maximum speed may be as low as 30 rpm or less (ratio up to 60:1). On the other hand, some very long twin screws for mixing can run at 600 rpm or faster, thus requiring a very low reduction rate and more deep cooling. If the reduction rate is incorrectly matched to the job, too much energy will be wasted. It may be necessary to add a pulley set between the motor and the first deceleration stage where the maximum speed is changed, which either increases the screw speed even beyond the previous limit or reduces the maximum speed. This increases the available energy, reduces the current value, and avoids motor failure, in both cases, the output may increase due to the material and its cooling needs.
If you still have questions, you can consult our company. Nanjing JlEYA is the leading professional manufacturer of twin screw extruders in China.