vertical twin screw extruder- China Factory Manufacturers Suppliers

Malfunctions that are caused by inadequate or improper maintenance can result in high repair costs and unnecessarily long gearbox down times. Regular servicing and inspection work are therefore imperative!
All servicing and repair work is only allowed to be performed with the gearbox stationary and by trained,authorized and appropriately instructed personnel.
Refilling lubrication oil
The oil level is to be checked regularly.It must never be below the bottom mark. In the case that the oil level drops below the minimum,it is imperative that the lubricant is topped up. The oil is only allowed to be topped up with the drive units shut down. A funnel with a filter is to be used for toppcng up (filter mesh 40um). The gearbox is always to be filled with the same type of oil as used previously It is not allowed to mix different oils or oils from different manufacturers.
Changing oil
The effectiveness of the oil reduces with increasing use due to soiling (foreign bodies and water)  and  chemical  changes(ageing  products).  When  the  soiling  and/or  ageing  is/are excessive, it is necessary to change the oil. Regular oil analyses provide information on the effectiveness of the gearbox oils. For larger quantities of oil it is recommended to make oil changes dependent on the results of an oil analysis.A missed oil change increases the risk of damage and can result in premature failure of the gearbox.
The first oil change should be made at approx.2500 perating hours.Subsequent oil changes depend on the state of the oil and are to be performed every 4,000 to 6,000 operating hours, however at the latest after one year.
The gear box is the core part of the twin screw extruders, we shall pay attention to its maintenance for long servicelife.

The twin screw extruder's standard equipment includes a sturdy base frame dedicated to housing the temperature control unit and oil lubrication system. The equipment features advanced control software for seamless integration into digital factories, ready for Industry 4.0, greatly improving ease of use. The following is a detailed description of the operating procedures of the twin screw extruder.

 

Here is the content list:

l Start up operation

l Stop the machine

l Precautions

 

Start up operation

1.Close the power main gate of the twin screw extruder.

2. Turn on the power at the operation panel: Press and hold the power button clockwise to turn and then release.

3. Set the temperature of each temperature zone: for example, a zone temperature according to the process requirements set the corresponding temperature, press the set button, and then adjust the up and down arrows to the desired temperature, press the set button.

4. Set the feeding rate: according to the process, requirements can be fed rate between 0 ~ 10 to set.

5. Set the host speed of the twin screw extruder: set the host speed between 0~30 according to the process requirements.

6. Add cooling water to the cooling tank.

7. In turn on the fan: press the operation button on the operation panel.

8. When you need to start the operation of the vacuum pump, you can start the vacuum pump.

9. Turn on the cutter switch.

 

Stop the machine

1. Twin screw extruder normal stopping sequence: stop the feeder: close the vacuum line valve, open the vacuum chamber on the cover; gradually reduce the main screw speed; shut down the pelletizer and other auxiliary equipment: off the motor, each external water inlet valve.

2. Twin screw extruder emergency stop: (1) in case of an emergency need to stop the host, you can quickly press the electrical control cabinet red emergency stop button, and the host and the feed speed knob back to zero, and then the total power switch off. After eliminating the fault, you can restart the machine again in normal driving order. (2) encounter equipment automatic protection trip stop: need to set the various parameters knob to zero, and then reset the parameters, press the reset button and start the machine again.

 

Precautions

1. The normal production of the first shift machine, be sure to first check whether the barrel, hopper seal is the original closed kind, such as changes or damage, should check the hopper, the machine inside the Jane there are no foreign objects.

2. Pay attention to the screw to start at a low speed, the air time can not exceed 3min.

3. Must pay attention to check the purity of each batch of material, do not allow any impurities mixed into the material.

4. The beginning of the material to pay attention to the first small amount, evenly added material, while paying attention to observe the current meter (torque meter) pointer changes.

For granular material, use metering to add material. When you first start to feed production, be sure to pay attention to the extruder production work overload phenomenon. After the forming die lip out of the material, and then gradually increase the screw speed as appropriate.

5. Often check the working condition of the motor carbon brush, abnormalities should be replaced or adjusted promptly.

6. The screw cleaning work is not allowed to use steel tools scraping material, the application of copper brush, shovel cleaning.

7. When the process temperature is suspected of displaying problems on the instrument, use mercury temperature, meter actual measurement of the machine Jane, and molding mold degree. Refer to the mercury temperature measured temperature, adjust the calibration instrument to show the temperature.

 

If you still have questions, you can consult our company. Our company's website is https://www.njjyextrusion.com/

The composition of the single screw extruder: mainly consists of servo motor, reduction box, screw cylinder, nozzle head, filter air, heating and cooling system, touch screen, and SPS control. It is the extrusion host to form.

• What are the reasons why the main engine of the single screw extruder cannot be started and the solutions?

• What are the reasons and solutions for the high inlet flow of the single screw extruder?

• What is the design concept of the single screw extruder?

What are the reasons why the main engine of the single screw extruder cannot be started and the solutions?

1. Reasons:

(1) The driving program of the single screw extruder is wrong.

(2) There is a problem with the main engine thread and whether the fuse is blown.

(3) The locking device for the single screw extruder and the main engine works.

2. Treatment:

(1) Check the program of the insert extruder and restart in the correct order.

(2) Check the main engine circuit.

(3) Check whether the lubricating oil pump has started and check the status of the locking device concerning the main engine. The oil pump cannot be turned on and the engine cannot be turned on.

(4) The inverter has not discharged the induction current, turn off the main power supply and wait five minutes before starting.

(5) Check if the emergency button of the single screw extruder has been reset.

What are the reasons and solutions for the high inlet flow of the single screw extruder?

1. Reasons: (1) The single screw extruder has an insufficient heating time and a large torque. (2) A certain section of the heating does not work.

2. Treatment method: (1) Use the handwheel when driving the single screw extruder. If it is not easy, extend the heating time or check that the heaters of the individual sections work properly.

The main engine makes an abnormal noise:

1. Reasons: (1) Main engine stock damaged. (2) A specific SCR in the SCR DC power supply of the main engine is damaged.

2. Treatment method: (1) Replace the main engine stock of the single screw extruder. (2) Check the thyristor alignment and replace the thyristor component if necessary.

What is the design concept of the single screw extruder?

1. High-speed and high-Yield extrusion based on high quality.

2. The design concept of low-temperature plasticization ensures the extrusion of high-quality products.

3. The two-stage overall design of the single screw extruder reinforces the plasticization function to ensure the adjustment of the high-performance extrusion.

4. Special barrier, comprehensive mixing design to ensure the mixing effect of materials.

5. High torque drop, extra-large pressure bearing.

6. Gears and shafts are made of high-strength alloy steel, cooled, and chipped.

7. High hardness, high finish, extremely quiet.

8. PLC-intelligent control can realize the connection between main and auxiliary machines.

9. The easy-to-monitor human-machine interface makes it easy to understand the processing and machine status.

10. The control method (temperature device) can be changed if necessary.

11. The material is 38CrMoAL/A nitric treatment, wear-resistant.

12 Strict temperature control accuracy, combined with air cooling and water cooling.

13. The single screw extruder has a unique inlet design and complete water cooling.

14. An single screw extruder with a grooved surface of the lower shell has an improved feed function that guarantees a high speed and a high yield of extrusion.

The single screw extruder is increasingly used in industrial production.Nanjing JlEYA has committed itself to offering the best-suited single screw extruders at a reasonable price, and all that is necessary to meet the needs of the customer.

Jieya team wish you have a nice holiday :)

(Nanjing Jieya is a professional manufacturer of twin screw compounding extruders with 20+ years experience and competitive price. We look forward to receive your inquiry.)

The single screw extruder is mainly composed of 3 parts: extrusion system, transmission system, and heating and cooling system. The following is a detailed introduction to the basic structure of the single screw extruder.

 

Here is the content list:

• Extrusion system

• Transmission system

• Heating and cooling system

 

Extrusion system

The main role of the extrusion system of the single-screw extruder is to melt and plasticize the polymer material to form a uniform melt, to realize the transformation from the glassy state to the viscous flow state. And in this process to establish a certain pressure, by the screw continuous extrusion delivery to the head die. Thus, the extrusion system plays an important role in the molding quality and output of the extrusion process.

The extrusion system mainly includes the feeding device, screw, and barrel, which is the most critical part of the extruder, of which the screw is the heart of the extruder, the material through the rotation of the screw in order to move in the barrel and get pressurized and part of the heat.

 

Transmission system

The drive system of a single screw extruder is usually composed of a motor, reducer, and bearing, whose role is to drive the screw and supply the torque and torque required by the screw in the extrusion process. During the extrusion process, the screw speed is required to be stable and does not change with the change of screw load to ensure the uniform quality of the product. However, in different situations, the screw is required to be able to achieve variable speed in order to achieve a machine that can adapt to the requirements of extruding different materials or products of different shapes. In most extruders, the change of screw speed is achieved by adjusting the motor speed. The drive system of the single-screw extruder is also equipped with a good lubrication system and a device for rapid braking.

 

Heating and cooling system

The heating and cooling system of a single screw extruder consist of a heating device and cooling device, which are necessary for the extrusion process to be carried out smoothly. The heating and cooling devices must ensure that the polymer materials are melted and plasticized and the temperature conditions during the molding process meet the process requirements.

The cooling device is generally set up in the extruder barrel, screw and hopper bottom, and other parts. Barrel cooling can be water-cooled or air-cooled, air-cooled is generally used for small and medium-sized single-screw extruders; large single-screw extruders are mostly water-cooled or a combination of the two forms. The cooling device at the bottom of the hopper is mainly to strengthen the solid material conveying effect, to prevent the material particles from becoming sticky due to the heating, blocking the material mouth and thus affecting the feeding. Generally, for extruders with a screw diameter of 90mm or more and high-speed extruders, a cooling device must be installed at the bottom of the hopper.

 

Our company focuses on twin-screw extruders, micro twin-screw extruders, plastic extruders, parallel twin-screw extruders, and other kinds of research and development and manufacturing as the core of the isotropic rotary twin-screw compounding extruder. If you still want to know more, you can consult our company.

Degradable plastics refer to a class of plastics whose various properties can meet the requirements of use, remain unchanged during the shelf life, and can be degraded into environmentally harmless substances under natural environment conditions after use. Therefore, it is also called environmentally degradable plastic.
There are a variety of new plastics: photodegradable plastics, biodegradable plastics, light/oxidative/biodegradable plastics, carbon dioxide-based biodegradable plastics, thermoplastic starch resin degradable plastics.
There are two main areas for the use of degradable plastics: one is the area where ordinary plastics were originally used. In these areas, the difficulty of collecting used or post-consumer plastic products will cause harm to the environment, such as agricultural mulch and single-use plastic packaging, and the second is areas where plastics are used instead of other materials. The use of degradable plastics in these areas can bring convenience, such as ball tacks for golf courses, and seedling fixing materials for tropical rainforest afforestation.
Specific applications are:
1.Agriculture, forestry and fishery, plastic film, water-retaining materials, seedling pots, seedbeds, rope nets, slow-release materials for pesticides and agricultural fertilizers.
2.Packaging industry, shopping bags, garbage bags, compost bags, disposable lunch boxes, instant noodle bowls, buffer packaging materials.
3.Sporting goods, golf tacks and tees
4.Hygiene products, women's hygiene products, baby diapers, medical mattresses, disposable haircuts.
5.Medical materials, bandages, clips, small sticks for cotton swabs, gloves, drug release materials, and surgical sutures and fracture fixation materials.
Nanjing Jieya also manufactures twin screw compounding extruder for bio-degradable material. We warmly welcome your inquiry.

Nanjing Jieya is a professional manufacturer of twin screw compounding extruders since 2004. Our extruders series include SHJ series, HT series, JY series, SJ series, etc. Today we will tell you the differences between SHJ series twin screw extruders and HT series high torque twin screw extruders from three main points below:

1. Torque grade

The torque rating grade of our SHJ series twin screw extruder is T/A3≤8 while HT series is 9≤T/A3≤13.5. Our HT series adopt high torque gear box, which is suitable for customers that pursuit high efficiency machines.

2. Power transmission

SHJ series use clutch for power transmission while HT series use torque protector, for example, R+W brand, Bibby brand, etc.

3. Output

The output of HT series twin screw extruder is much higher than SHJ series.

So HT series can further improve the performance of extruders.But surely, price is higher than SHJ series.

PVC compounding extruder is made by mixing PVC resin with stabilizers, lubricants, and other additives through granulation and then extrusion, or by using powder in one extrusion. what are the application areas of PVC? The following are the details.

 

Here is the content list:

• General soft products

• PVC film

• PVC foam products

• PVC coated products

• PVC paste resin

• PVC transparent sheet

• PVC rigid sheet

• Other applications of PVC

 

General soft products

General soft products can be extruded into cables, wires, and hoses by the extruder: shoe soles, slippers, various plastic sandals, as well as toys and auto parts by the injection molding machine with various molds.

 

PVC film

PVC film After mixing and plasticizing PVC with additives, transparent or colored film of specified thickness can be made by using a three-roller or four-roller calendar, and calendered film can be processed by this method. It can also be cut and heat laminated to process raincoats, tablecloths, curtains, packaging bags, inflatable toys, etc. The wide transparent film can be used for greenhouse, plastic shed, and ground film; the film stretched in both directions can be used for shrink packaging due to its characteristics of shrinkage by heat.

 

PVC foam products

Soft PVC can be used as sandals, insoles, foam slippers, and shockproof and cushioning packaging materials. In addition, it can also be extruded into low-foaming hard PVC sheets and profiles by extruder, which is a new type of building material and can be used as a substitute for wood.

 

PVC coated products

Artificial leather with backing is made by coating PVC paste on cloth or paper and then plasticizing it at 100 degrees Celsius or above (or PVC and additives can be calendered into film and then pressed together with backing); while artificial leather without backing is directly calendered by calender into soft sheet with a certain thickness and then pressed with the pattern. It can be used to make leather bags, leather boxes, book covers, sofas, and car cushions, etc. It can also be made into flooring leather, which is used as the flooring material for buildings.

 

PVC paste resin

PVC emulsion or micro-suspension resin is dispersed in a liquid plasticizer to make it swell and plasticize into the plasticized sol, and then add stabilizer, filler, coloring agent, etc. After full stirring for de-bubbling, PVC paste is prepared, and then processed into various products such as coat hangers, tool handles, Christmas trees, etc. by casting, impregnating, or laminating processes.

 

PVC transparent sheet

Impact modifier and organotin stabilizer are added to PVC, which is mixed, plasticized, and calendered into transparent sheets. Then it can be made into thin-walled transparent containers by thermoforming and can be used for vacuum blister packaging such as moon cake boxes, etc. It is an excellent packaging material and decoration material.

 

PVC rigid sheet

PVC hard sheet and plate After adding stabilizer, lubricant, and filler to PVC and mixing, it can be extruded into various caliber hard pipes, shaped pipes, corrugated pipes, and other products by using an extruder, and used as a downpipe, drinking water pipe, electric wire casing or staircase handrail, etc.; the calendered sheet can be overlapped and hot-pressed to make various thicknesses of hard sheets, which can be cut into various desired shapes and can be welded into various chemical resistant tanks, ducts and containers by using PVC welding rod with hot air, etc.

 

Other applications of PVC

PVC can be processed into rigid profiles using an extruder and used for window and door assembly. In some countries, the doors and windows assembled by PVC rigid profile have occupied the market of windows and doors together with wooden windows and doors, aluminum windows, etc.

 

If you want to buy PVC compounding extruder, you can consult our company, our company's website is https://www.njjyextrusion.com/

Customized high pressure blowing film extruder machine plastic blow film extrusion machine for ldpe lldpe, US

If you need polymer extruder machine, the options will usually fall into either single screw or double screw categories. Generally speaking, double screw polymer extruder machine will be more efficient and faster to use, as the inclusion of two screws effectively doubles production capacity. But the cost of these plastic extruders is higher and ...

For some applications Conical Twin Screw Extruder types are an excellent choice ... Output Capacity-Pipe: 100-110: 100-120: 130-150: 250-280: 400-450: 750-850 ... 3800: 4500: 5370: 6380: Dimension-Width (mm) 1200: 1250: 1300: 1380: 1500: 1650: Dimension-Height (mm) 2100: 2300: 2300: 2300: 2400: 2450 . Conical Twin Screw Extruders - High Torque ...

The basic techniques for optimizing capacity of side feeders is presented in this webinar. While various aspects of side feeding have been described in previous webinars, all of …

1 SJSZ Series Conical Double-screw Extruder. SJSZ series PVC conical twin-screw extruder is composed of barrel screw,gear transmission system, measurable feeding,vacuum deaerating, heating, cooling and electronic control components etc. Conical twin-extruders are special equipments which can extrude and mold by using various kinds PVC …

Plastic Twin Screw Extruder /Parallel Double Screw Extruder Machine For Pelletizing LCL woden case, FCL with film and rope fixing: Delivery Time: Plastic Twin Screw Extruder /Parallel Double Screw Extruder Machine For Pelletizing 20 - 45 work days: Payment Terms: L/C, T/T, D/P, Western Union, MoneyGram:

HKY35 twin screw compounding and granulating extruder, US

PET 50% TiO2 High Filling Masterbatch Twin Screw Extruder Machine, find complete details about PET 50% TiO2 High Filling Masterbatch Twin Screw Extruder Machine, twin screw extruder, masterbatch machine, …